Personlized Products Pilha Zinco - 1.5V R20 UM1 Heavy Duty D Battery – Sunmol

Introduction

Overview

This specification specifies the technical requirements for the Anita R20P carbon zinc-manganese dry cell. If no other detailed requirements are listed, the battery technical requirements and dimensions should meet or exceed GB/T8897.1 and GB/T8897.2.

1.1 Citation standards

GB/T8897.1 (IEC60086-1,MOD)(Primary battery Part 1:General)

GB/T8897.2 (IEC60086-2,MOD) (Primary battery Part 2: External dimensions and technical requirements)

GB8897.5 (IEC 60086-5,MOD) (Primary batteries Part 5: Safety requirements for electrolyte batteries in aqueous solution)

1.2 Environmental standards

The battery complies with the EU 2006/66/EC Battery Directive

Electrochemical system, voltage and nomenclature

Electrochemical system: zinc – manganese dioxide (ammonium chloride electrolyte solution), mercury-free

Nominal voltage:1.5V

Name:IEC: R20P ANSI: D JIS:SUM-1 Others: 13F

Battery size

Battery meets sketch requirements

3.1 Acceptance tools

Measured with an accuracy of not less than 0.02mm vernier calipers, measurement to prevent short-circuiting of the battery, one end of the calipers should be affixed to a layer of insulating material.

3.2 Acceptance method

The use of GB2828.1-2003 normal inspection of a sampling program, special inspection level S-3, receiving quality limit AQL = 1.0

Product Features

Battery weight and discharge capacity

Battery weight about: 82g

Discharge capacity: 4700mAh(load 10Ω, 4h/day, 20±2℃, RH60±15%, termination voltage 0.9V)

Open circuit voltage, load voltage and short circuit current

Technical Requirements

Discharge capacity

Compliance with minimum average discharge time:

1. Test 9 batteries for each discharge mode;

2. The average discharge value of 9 batteries is greater than or equal to the specified value of the minimum average discharge time, and the number of batteries whose single-cell discharge time is less than 80% of the specified value is not more than 1, then the battery electrical performance test of the batch is qualified;

3. If the average discharge value of 9 batteries is less than the specified value of the minimum average discharge time and (or) the number of batteries less than 80% of the specified value is greater than 1, then another 9 batteries are tested and the average value is calculated. If the calculation result meets the requirements of Article 2, the electrical performance test of the batch of batteries is qualified. If not, the battery electrical performance test of the batch is unqualified and no further testing.

Packaging and Marking

Liquid leakage resistance performance requirements

Safety performance requirements

Cautions

Logo

The battery body is marked with the following markings.

1. Model: R20P/D

2. Manufacturer or trademark: Sunmol ®

3. Battery polarity: “+” and “-”

4. shelf life of the deadline or the year of manufacture

5. Precautions for safe use

Precautions for use

1. This battery is not rechargeable. If you charge the battery, there may be danger of battery leakage and explosion.

2. Make sure to insert the battery correctly according to the polarity (+ and -).

3. It is forbidden to short-circuit, heat, throw into fire or disassemble the battery.

4. The battery should not be over-discharged, otherwise the battery will swell, leak or the positive cap will top out and damage electrical appliances.

5. New and old batteries, batteries of different brands or models cannot be used together. It is recommended to use batteries of the same brand and the same model when replacing.

6. The battery should be removed when the electric appliance is not used for a long time.

7. Take out the exhausted battery from the electric appliance in time.

8. It is forbidden to weld the battery directly, otherwise the battery will be damaged.

9. The battery should be kept away from children. If swallowed accidentally, seek medical attention immediately.

Reference Standards

Conventional packaging

Each 12 sections are packed into 1 inner box, 12 boxes are packed into 1 case. Also can be packaged according to customer requirements, the actual number of boxes marked by the box mark shall prevail.

Storage and expiration date

1. The battery should be stored in a well-ventilated, cool and dry place.

2. The battery should not be exposed to direct sunlight or placed in the rain for a long time.

3. Do not mix and stack the batteries with their packaging removed.

4. Store at 20℃±2℃, relative humidity 60±15%RH, the battery storage period is 2 years.

Discharge curve

Typical discharge curve

Discharge environment: 20℃±2℃, RH60±15%

As the product technology is updated and the technical parameters are adjusted, the specifications will be updated at any time, so please contact ENITA in time to obtain the latest version of the specifications.

FAQ

Q1. How about your battery delivery time?

A: Within 35 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q2: How do you make our business long-term and good relationship?

A:1. We keep good quality and competitive price to ensure our customers benefit ;

Q3. What is your terms of payment?

A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages before you pay the balance, OR LC at sight , DP

Childproof your batteries

Keep your batteries where children can’t reach them. As with every small object, children may swallow batteries if they handle them incorrectly. Coin batteries are especially dangerous if they’re swallowed, as they could get stuck in a child’s smaller throat and cause suffocation. If that happens, immediately get to your nearest emergency room.

Battery safety isn’t rocket science – it’s common sense. Be on the lookout for these pitfalls and you’ll be able to use your batteries optimally.