Factory making Pil R6 - 1.5V R6 UM3 Heavy Duty AA Battery – Sunmol

Introduction

Scope

This specification governs the technical requirements of Sunmol Carbon Zinc battery of R6P/AA. If it doesn’t list the other detailed requirements, the technical requirements and dimensions of battery should meet or above GB/T8897.1 and GB /T8897.2.

1.1Reference Standards

GB/T8897.1 (IEC60086-1, MOD)(Primary Battery Part 1: General）

GB/T8897.2 (IEC60086-2, MOD)（Primary Battery Part2: Size and Technical requirements）

GB8897.5 (IEC 60086-5, IDT)（Primary Battery Part5: Safety of batteries with aqueous electrolyte）

1.2Environmental Protection Standard

The battery meets the standard of EU battery directives 2006/66/EC.

Chemical system, Voltage and Designation

Electrochemical system: zinc – manganese dioxide (ammonium chloride electrolyte  solution), does not contain mercury

Nominal voltage: 1.5V

Naming: IEC: R6P     ANSI: AA     JIS: SUM-3     Others: 15F

Battery Size

Conform to the requirements of the brief

3.1 Acceptance tool

Using vernier caliper measurement precision is not less than 0.02 mm, measure to prevent the battery short circuit, one end of the caliper head card should be labeled as a layer of insulating materials.

3.2 Acceptance methods

The GB2828.1-2003 normal inspection sampling plan at a time, special inspection level S-3, acceptance quality limit AQL=1.0

Product Features

Weight and discharging capacity

Typical Weight: 14.0g

discharge capacity: 800mAh(load 43Ω, 4h/day, 20±2℃, RH60±15%, final voltage 0.9V)

open-circuit voltage, closed – circuit voltage and short-circuit current

Technical Requirements

Discharging Ability

Satisfaction Standard:

1. 9 pieces of battery will be tested for each discharging standard;

2. The result of the average discharging time from each discharging standard shall be equal to or more than the average minimum time requirement; no more than one battery has a service output less than 80% of the specified requirement. Then the batch battery performance test qualified.

3. If nine section of the battery discharge average less than the specified value of minimum average discharge time and (or) is less than the specified value of 80% of the battery number more than 1, we should take another 9 batteries to test again and calculate the average. Calculation results conform to the requirement of article 2, the batch battery performance test qualified. If it does not conform to the requirement of article 2, the batch battery performance test is unqualified, and no longer test.

Packaging and Marking

Anti-leakage ability

Safety Characteristics

Cautions

Signs

The following markings will be printed, stamped or impressed on the body of battery:

1. Designation: R6P/ AA

2. Manufacturer or trademark：Sunmol ®

3. Polarity：“+”and“-”

4. Expiration date deadline or manufacturing time

5. The attention notes for safe use.

Cautions for Use

1. Since the battery is not manufactured for recharging, there are risks of electrolyte leakage or causing damage to the device if the battery is charged.

2. The battery shall be installed with its “+” and “-” polarity in a correct position, otherwise may cause short-circuit.

3. Short-circuiting, heating, disposing of into fire or disassembling of battery is prohibited.

4. Battery can not be forced discharged, which leads to excess gassing and may result in bulging, leakage and de-crimping of cap.

5. New batteries and used ones can not be used at the same time. It is recommended to use the same brand when replacing batteries.

6. Electrical appliances should be take out the battery when not in use for a long time

7. Exhausted batteries shall be removed from the compartment in order to prevent over-discharge.

8. Prohibit direct welding battery, otherwise it will damage the battery.

9. Battery are to be kept away from children. If swallowed, contact a physician at once.

Reference Standards

Normal Packing

Every 2 or 3 and 4 batteries or according to customer requirements with transparent membrane after hot shrinkage, each 60 knots in 1 inner boxes, 16 boxes into 1 box.

Storage and shelf life

1. Batteries should be stored in ventilated, cool and dry place.

2. The battery should not be exposed to direct sunlight for a long time or in the rain.

3. Not to mix removed packaging battery stack together.

4. Stored at condition of tempreture20℃±2℃, relative humidity 60±15%RH, the battery shelf life is 2 years.

Discharge curve

Typical discharge curve

Discharge environment: 20℃±2℃, RH60±15%

With parameter adjustment, product technology updates, technology specification will update at any time, please do not hesitate to contact to stand for the latest version of the specification.

FAQ

Q1.Is this product safe?

A: Anti short circuit & Anti scald, Anti explosion,Environmental friendly.

Q2. Could you do customer brand?

A:Of course ,we could provide professional OEM service.

Q3.What’s the MOQ?

A:Small quantity is OK for trial order or samples if we have stock,customize brand or customize request please contact us.

Advantages

“Customer First, Service Foremost” is our service philosophy. We put considerable effort into optimizing our order fulfillment service to meet each client’s satisfaction. Also, we are committed to building long-term relationships with our clients.Our company is able to meet the developed demands of clients with excellent quality batteries, preferential prices and perfect service. Both OEM and ODM orders are welcome.  

battery leakage

Batteries don’t normally leak on their own. Leakage is most often caused by improper contact or by leaving them in unused devices. If you notice chemical discharge, be sure not to touch it. Try removing the batteries with a paper towel or a toothpick. Dispose of them at your nearest recycling point.

Was established in December 1997, with 25 years of development experience, Sunmol battery is proud to be a factory of alkaline battery, zinc carbon battery,AG alkaline button battery and a series of CR lithium button battery. The products are widely used in remote controls, cameras, electronic dictionaries, calculators, watches, electronic toys and other electronic appliances.

All of our equipment are from the Germany and Japan, we learned the advanced technology from them in the meantime. With the good homemade packaging & printing producing lines and the newly tester, accompany our skillful people and hard-working staff. 

The company’s advanced production equipment, sophisticated testing equipment, and standardized management provide a reliable guarantee for the stability and improvement of product quality. A large amount of capital has been invested in new product development and technological innovation, and a large number of high-tech talents have been introduced. At present, we are exported more than 5,000 millions batteries annually.