100% Original R6c Battery - 1.5V R14 UM2 Heavy Duty C Battery – Sunmol

Introduction

Overview

This specification stipulates the technical requirements of Anida R14P carbon zinc manganese dry battery. If other detailed requirements are not listed, the battery technical requirements and dimensions should meet or exceed GB/T8897.1 and GB/T8897.2.

1.1 Reference Standard

GB/T8897.1 (IEC60086-1, MOD) (Primary Battery Part 1: General Provisions)

GB/T8897.2 (IEC60086-2, MOD) (Primary battery Part 2: Dimensions and technical requirements)

GB8897.5 (IEC 60086-5, MOD) (Primary battery Part 5: Safety requirements for aqueous electrolyte batteries)

1.2 Environmental standards

The battery complies with EU 2006/66/EC battery directive

Electrochemical system, voltage and naming

Electrochemical system: zinc-manganese dioxide (ammonium chloride electrolyte solution), no mercury

Nominal voltage: 1.5V

Designation: IEC: R14P ANSI: C JIS: SUM-2 Others: 14F

Battery size

The battery meets the requirements of the sketch

3.1 Acceptance tools

Use a vernier caliper with an accuracy of not less than 0.02mm to prevent battery short circuit during measurement. One end of the caliper should be pasted with a layer of insulating material.

3.2 Acceptance method

Adopt GB2828.1-2003 normal inspection one-time sampling plan, special inspection level S-3, acceptance quality limit AQL=1.0

Product Features

Battery weight and discharge capacity

Battery weight: 40g

Discharge capacity: 1200mAh (load 3.9Ω, 24h/day, 20±2℃, RH60±15%, termination voltage 0.9V)

Open circuit voltage, load voltage and short circuit current 

Technical Requirements

Discharge capacity

Compliance with minimum average discharge time:

1. Test 9 batteries for each discharge mode;

2. The average discharge value of 9 batteries is greater than or equal to the specified value of the minimum average discharge time, and the number of batteries whose single-cell discharge time is less than 80% of the specified value is not more than 1, then the battery electrical performance test of the batch is qualified;

3. If the average discharge value of 9 batteries is less than the specified value of the minimum average discharge time and (or) the number of batteries less than 80% of the specified value is greater than 1, then another 9 batteries are tested and the average value is calculated. If the calculation result meets the requirements of Article 2, the electrical performance test of the batch of batteries is qualified. If not, the battery electrical performance test of the batch is unqualified and no further testing.

Packaging and Marking

Liquid leakage resistance performance requirements

Safety performance requirements

Cautions

 Identification

The following marks are marked on the battery body:

1. Model: R14P/C

2. Manufacturer or trademark: Sunmol ®

3. Battery polarity: “+” and “-”

4. Deadline of shelf life or manufacturing year and month

5. Precautions for safe use

Precautions for use

1. This battery is not rechargeable. If you charge the battery, there may be danger of battery leakage and explosion.

2. Make sure to insert the battery correctly according to the polarity (+ and -).

3. It is forbidden to short-circuit, heat, throw into fire or disassemble the battery.

4. The battery should not be over-discharged, otherwise the battery will swell, leak or the positive cap will top out and damage electrical appliances.

5. New and old batteries, batteries of different brands or models cannot be used together. It is recommended to use batteries of the same brand and the same model when replacing.

6. The battery should be removed when the electric appliance is not used for a long time.

7. Take out the exhausted battery from the electric appliance in time.

8. It is forbidden to weld the battery directly, otherwise the battery will be damaged.

9. The battery should be kept away from children. If swallowed accidentally, seek medical attention immediately.

Reference Standards

Regular packaging

There is 1 inner box for every 12 sections, 24 boxes in 1 carton. It can also be packaged according to customer requirements, and the actual quantity indicated on the box mark shall prevail.

Storage and validity period

1. The battery should be stored in a well-ventilated, cool and dry place.

2. The battery should not be exposed to direct sunlight or placed in rain for a long time.

3. Do not mix the batteries with the packaging removed.

4. When stored at 20℃±2℃, relative humidity 60±15%RH, the battery shelf life is 2 years.

Discharge curve

Typical discharge curve

Discharge environment: 20℃±2℃, RH60±15%

With product technical updates and technical parameter adjustments, the specifications will be updated at any time, please contact Anida in time to obtain the latest version of the specifications.