1.5V AG13 AG10 AG series Alkaline Button Cell Battery – Sunmol
1.5V AG13 AG10 AG series Alkaline Button Cell Battery – Sunmol Detail:
Introduction
Scope of application
This standard describes the external dimensions, characteristics, technical requirements and precautions of alkaline zinc-manganese button AG13 batteries. This standard applies to the alkaline zinc-manganese button AG13 battery produced by Dongguan Sunmol Battery Co., Ltd.
Definition
2.1 Nominal capacity.
It re f e r s to the discharge capacity when discharging continuously with 1KΩ at 20±2℃ to the termination voltage of 0.9V.
Product Model and Size
3.1 Product Model
AG13 alkaline zinc-manganese coin cell
3.2 Product Size
Product Features
| Projects | Characteristics |
| Nominal capacity | 140mAh |
| Nominal voltage | 1.5V |
| Discharge termination voltage | 0.9V |
| Humidity range | 60±15%RH (non-condensing) |
| Product Size | Maximum height：5.4mm Maximum diameter：Φ11.6mm |
| Average weight | 1.98g |
Technical Requirements
Test Environment
Unless otherwise stated, all tests were performed at a temperature of 20±2°C and a relative humidity of 60±15%.
|
Serial number |
Projects |
Test conditions |
Judgment criteria |
|
5.2.1 |
Storage Performance |
Sampling plan: MIL-STD-105E, general levelⅡ, single sampling method, AQL=0.4 Note: Load voltage test method: 6.8KΩ/0.3 seconds, initial system The test must be carried out within 30 days after delivery |
No-load voltage (V) Load voltage(V) Initially made: 1.55 / 1.50 |
|
5.2.2 |
Discharge performance |
Discharge load: 22kΩ; discharge time: 24 hours/day continuous discharge; termination voltage: 1.2V Note: Prefabricated cells must be tested within 30 days of delivery |
Initially made ≥ 600 hours Storage at room temperature for 12 months ≥ 540 hours |
|
Discharge load: 1kΩ; discharge time: 24 hours/day continuous discharge; termination voltage: 0.9V Note: Prefabricated cells must be tested within 30 days of delivery |
Initially made ≥ 100 hours Storage at room temperature for 12 months ≥ 90 hours |
||
|
5.2.3 |
Short circuit performance |
Short circuit 24 hours at 20±2℃ |
No explosion N=5, Ac=0, Re=1. |
And 5.2.3 Acceptance criteria.
1. Nine cells were discharged for each discharge condition.
2. The average discharge time is equal to or greater than the specified value of the minimum average discharge time, and no battery discharge time is less than 80% of the specified value, the battery discharge time is considered to meet the requirements.
3. If the above results do not pass, you can repeat the test again.
Shelf life
1 year storage at room temperature and suitable environment, after 1 year storage, the battery can retain 90% capacity
Packaging and Marking
Packaging and marking can be done according to customer requirements. In the absence of special requirements, the following are generally marked on the battery.
Logo Design
1. Battery model: AG13
2. Battery type: Manufacturer’s name “Sunmol” & “DG Sunmo”
3. The polarity mark “BUTTON CELL +” is marked on the positive terminal of the battery
Packaging pictures
Cautions
1. It is prohibited to charge the battery, which may lead to battery leakage, heat, or even explosion and fire.
2. When installing the battery, please install the battery in the correct direction to avoid damaging the battery by over-discharging or back-charging, which may even cause battery leakage, heat, rupture and fire.
3. It is forbidden to short-circuit, heat, put the battery into fire, or attempt to disassemble it.
4. It is forbidden to over-discharge the battery, which may lead to battery leakage or danger.
5. It is forbidden to use the new battery and the used battery at the same time.
6. Please remove the depleted battery from the appliance to avoid over-discharging the battery and causing it to leak.
7. It is forbidden to weld the battery to avoid damaging the insulation ring and the protection device.
8. Please do not place the battery in the hands of infants and children to avoid accidentally swallowed, in case of swallowing, please seek medical attention immediately.
9. It is forbidden to take the battery apart, destroy the battery casing and modify the battery to avoid a short circuit, which will eventually lead to battery leakage, or even rupture and fire.
If the product leaks and electrolyte gets into your eyes, do not rub, flush your eyes with water, and if necessary, go to a hospital immediately for treatment, otherwise your eyes will be injured.
If the product emits odor, heat, discoloration, deformation or any abnormalities occur during use or storage, immediately remove the product from the unit and discontinue use.
Reference Standards
GB/T 8897.1-2008 Primary Battery Part 1: General Provisions
GB/T 8897.2-2008 Primary battery Part 2: External dimensions and electrical performance requirements
GB/T 8897.3-2006 Primary battery Part 3: Watch battery
GB/T 8897.5-2006 Primary Battery Part 5: Safety requirements for electrolyte batteries in aqueous solution
Discharge curve
Product detail pictures:
Related Product Guide:
We keep on with the theory of "quality first, provider initially, constant improvement and innovation to meet the customers" with the management and "zero defect, zero complaints" as the standard objective. To great our company, we deliver the merchandise using the fantastic excellent at the reasonable price for 1.5V AG13 AG10 AG series Alkaline Button Cell Battery – Sunmol , The product will supply to all over the world, such as: Madagascar, Armenia, Russia, Our advanced equipment, excellent quality management, research and development ability make our price down. The price we offering may not be the lowest, but we guarantee it is absolutely competitive! Welcome to contact us immediately for future business relationship and mutual success!
By Honorio from Oslo - 2018.05.13 17:00
This is a honest and trustworthy company, technology and equipment are very advanced and the prodduct is very adequate, there is no worry in the suppliment.
By Doris from France - 2017.04.08 14:55
